This warranty does not cover normal wear and tear. Applications: Disconnects air systems on brakes, suspension, steering, engine, transmission and other auxiliary equ. For Tool Sets without Seals: and Need More Info? Includes detailed axle shaft oil seal replacement procedures, tool recommendations, and torque specifications that you need to correctly perform inner seal replacement plus check the gear backlash on your Ford Excursion or 1999-2004 Ford F250, F350, F450, or F550 Super Duty® 4x4 Dana Spicer Model 50 or Model 60 front axle. We usually respond within 24 hours. Interactive Exploded View Need More Info? Also covers basic Front Brake Service. We usually respond within 24 hours.
All non-paying bidders will be reported! We will replace this product, if found to be defective, when accompanied with the original sales receipt. Since they are just an outer protective seal, a failed one does not pose any real problem, although it is of course better to have them functional. Each tool is double-ended to disconnect air lines even in hard-to-reach areas. The extra time needed to replace these components is minimal since you already have the axle apart to do the axle seals. The Ford 4x4 Dana 60's have the drivers side drop, both standard low pinion and reverse cut high pinion gears and kingpin steering knuckles up to about 1991 and in 1992 they started using ball joints in the steering knuckles.
This can be caused by age, lack of lubrication, or wear from the axle itself. Order 2 Seals per vehicle. Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project! For 1999-2004 vehicles, is made it fit through Plastic Axle Shaft Guides which are located in the axle tubes just outboard of the inner axle shaft oil seals. Like most seals, an axle seal can fail over time. In 2000 Ford F-450 and F-550 4x4 models also used the Dana 60 front axles and starting in 2005 the F-450 and F-550 had the Super 60 front axles. Tech Note 5: Seal Remover Tool Once the axle is disassembled, the old seals can be easily removed with our Seal Remover Tool Set or another suitable tool such as a length of sturdy pipe that will fit inside the axle tube and oil guide. Most of them will be worn out within 3 or 4 years.
Tech Note 3: When Installing Seals The inner axle seals used on 1999 and newer Model 50 and 60 Ford front axles are interchangeable, however, the depth the seals are installed in the housing is different. Smaller end fits in tight spots. We will replace this product, if found to be defective, when accompanied with the original sales receipt. Lisle 56650 Adjustable Seal Puller. Two hook sizes easily remove most oil and grease seals. This warranty does not include labor, incidental or consequential damages and is void if the product was not properly installed and maintained or used in an application for which it is not listed in the Spicer Catalog.
Close to 400 color photographs, color Exploded Views and Parts Guide. An axle seal allows the axle shaft to stay lubricated without leaking gear oil onto the wheels or ground. To get the correct seal depth when using with a Model 60 axle do this: Before you take out the old seals, place Seal Installer in the old seal and scribe a mark on the tool at the axle bore face. I have seen in everyone's posts that I have looked at and researched and no one has addressed this issue. If you see oil leaking past this seal, you need Inner Axle Seal.
Dan the Gear Man® Tech Notes: Tech Note 1: Maximize Seal Life To maximize dust seal life and prevent squeaks, apply a thin, uniform coat of a quality grease to the seal lip. This can be due to low gear oil levels. If you would prefer Seal, the correct Installer is which is available separately or in these Tool Sets and Kits for Ford: Tool Only Set for 1999-2005 Dana 50 Inner Axle Seal and Tool Set for 1999-2005 Dana 50 Tool Only Set for 1978-current Dana 60, Dana Super 60 Inner Axle Seal and Tool Set for 1978-current Dana 60, Dana Super 60 Tech Note 8: Available Tool Sets Already have the Seals? Just click on the link to e-mail us. Feel free to ask us! Use with a hammer to install the axle seal onto the axle shaft. Thanks for any and all thoughts, ideas and this sight is better than a service manual! Cap is made of steel so it can be replaced if needed. The end of the axel housing is all scaly and rusty - is a seal expected to seal on there and last??? Functionally, the seals are interchangeable on 1999 to current Ford Dana 50, Dana 60, and Dana Super 60 front axles, but they do require different installers.
Item Compatibility List Year Make Model Trim Engine Notes 2005 Ford Excursion Eddie Bauer Sport Utility 4-Door 5. The axle seal may be the source of the leak. For Ford 1999-2004 Super Duty®, please refer to these 4x4 Tech Publications for service procedures: Includes 5 pages of Step-by-Step procedures with 17 full-color photographs. Repairing his axel hub bearings seals. After 10 days a non-paying bid alert will be filed with eBay.
The adjustable head works great on front wheel drive transaxles. Front Axle Tech Manual for Ford Excursion and 1999-2004 Super Duty is a 17 page, color illustrated, step-by-step printed shop repair manual that includes our four Tech Service Bulletins plus Front Axle Exploded Views. The only special tool you need to install these are your two thumbs to push them on. This warranty does not cover normal wear and tear. We offer same-day shipping on most items we sell if order is paid for by 3:00 p. For 2005 and newer Super Duty trucks, Inner Seal Replacement is identical. Image is representative of product, but may vary from actual item.