So then I took it to my mechanic who has been working on it and becoming frustrated. Does not require splitting tractor. It's all about sharing and helping out tractor owners especially newbies. Any thoughts why this is happening? There are 3 main types of Ford Tractor manuals, each with a specific purpose. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited.
It is installed but not working. None of these trademark holders are affiliated with Yesterday's Tractor Co. These manuals cover either the engine only or chassis only. Hate to tell you but thats a common problem. Dean Tractor Guru Joined: 29 Jan 1998 Posts: 18792 Posted: Sat Sep 10, 2011 4:42 pm Post subject: Re: Ford 641 Workmaster won't idle Always verigy that the ignition is spot on before trying to adjust a carburetor.
So far the 2 books work well together. The turnaround was fast and the repair was great. Walt's Tractor Parts has these tubes, and probably others can supply them as well. When diagnosing an issue, or showing off your tractor or implement, it's important to add images so we all know what you're talking about. Redid the carb and located a a port that was clogged and needed ultra small drill bits and wire to clean out 50 years of crud.
Included in every manual: troubleshooting section to help identify specific problems; tips that give valuable short cuts to make the job easier and eliminate the need for special tools; notes, cautions and warnings for the home mechanic; color spark plug diagnosis and an easy to use index. Parts, Owners and Service Manuals are typically available for your Ford 641 Tractor. He told be that the problem was in the steering box. Covers series 501, 600, 601, 700, 701, 800, 801, 900, 901, 1801, 2000 4-Cyl. To see current photo ads, click. Looks like I have the tractor that you have to split the engine off of the case.
Cleaned carb numerous times, checked ignition, etc. Success on stopping it is less common. Otherwise he would have tried to get it running first. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. The guy will not take the tractor back so I am left to figure this out I guess. I had the original 6 volt generator rebuilt into a 12 volt generator. Idles and runs like a dream now.
Loosen all the crank bearings and it will drop some. I am a very serious collector of Ford tractors. It was also available as an orchard tractor, the 641-21. I opened the side drain for my transmission and found the missing hydraulic oil. It is written in the language of a mechanic and may include valuable detailed information such as specifications, torques, ranges, etc.
Yesterday's Tractors - Antique Tractor Headquarters. If you have the shop manual it is shown on page 100, Fig. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. The high pressure line develops leaks due to corrosion and transfers hydraulic fluid from the hydraulic reservoir to the transmission. None of these trademark holders are affiliated with TractorShed. When the page resets hit search again, it will pull up old posts. I'm looking for any advice before I start blocking up the frame and start removing the cowling and accessories.
Most of our stocked parts ship the same day you order M-F. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. This motor had a liquid cooling system and a compression ratio of 7. I guess i will have to find some gaskets and o-rings from somewhere. John Deere and its logos are the registered trademarks of the John Deere Corporation. John Deere and its logos are the registered trademarks of the John Deere Corporation. It would not start and the spark seemed real weak so I tried replacing the coil and some wires then I had no spark.
Jon Barrett New User Joined: 10 Sep 2011 Posts: 4 Posted: Sat Sep 10, 2011 6:39 pm Post subject: Re: Ford 641 Workmaster won't idle where is that port located? It ain't a competition so why the admins here feel threatened is beyond me. This tractor was part of Ford's 601 Workmaster series, a lineup of tractors that are used for mowing, baling, moving and loading. None of these trademark holders are affiliated with Yesterday's Tractor Co. If they just accept reality and get over it they'll be happier. Upon buying he tractor the hydraulics were not working that great. I am sure many will agree with me.
I'm thinking that if I have to remove the engine, it might time to overhaul the engine. Its not that hard to install bearings while your in there. We use it everyday on our small farm. Each manual contains easy to follow step-by-step instructions linked to hundreds of photographs and illustrations. What they sell you are parts supplied by a handful of part suppliers who donate to their site as sponsors.